How to Get Popsocket to Stick Again

Download Article

Download Article

PopSockets are very useful for getting a meliorate grip on your phone, simply they can get muddy with time and the agglutinative that sticks it to the back of your telephone can become loose and lose its stickiness. After removing it from your phone, simply soak it in water and scrub it with soapy water your PopSocket to brand information technology look good as new and stick as if you bought it yesterday.

1. i

   Fill up a shallow dish with cold tap water. Grab a shallow dish, such as a small bowl or a deep plate, and fill it with about .5 in (i.3 cm) of very cold tap h2o. This is to ensure that you only soak the agglutinative side of the PopSocket — you should make clean the plastic grip separately.

   • Fifty-fifty if your PopSocket is larger than normal, using only a .5 in (ane.3 cm) layer of h2o will ensure that but the adhesive side touches the h2o when it is extended.

2. 2

   Remove the popsPopSocketocket and identify it pasty-side down in the water. Dig your fingernail under the PopSocket to pry it off of your telephone, then pull the plastic grip to it extend to its full length. Place the adhesive side down in the water so the plastic grip pokes above the surface of the water.

   • Be sure that your extended PopSocket rises above the surface and drain out h2o as necessary to avert getting the rest of information technology moisture.^[1]

   Advertisement

3. 3

   Let the PopSocket soak for most 10 seconds, and so remove it. Don't disturb the water and don't take it out before 10 seconds are up. Once x seconds have passed, chop-chop take it out of the water by the grip and shake off any excess h2o. Exercise not let it soak for more than than 10 seconds or it could ruin the adhesive. ^[2]

   • If you are concerned most ruining the adhesive, run the PopSocket nether cold h2o for a few seconds instead, although soaking it is more effective.^[3]

4. 4

   Lay a paper towel downwardly and place the PopSocket sticky-side upwardly. You tin can utilize a regular kitchen towel or a linen towel, depending on what you have readily available. Lay the PopSocket with the viscous side pointing up and the design and plastic grip touch the paper.^[4]

5. 5

   Let the agglutinative side of the PopSocket dry for 10 minutes. Go out your PopSocket to dry for ten minutes at nearly, and go along an center on information technology every bit it dries to run into if it finishes sooner.^[5] Avoid using a pilus dryer or dabbing it with a towel or you lot could damage the agglutinative and make it less sticky. Just let information technology air dry, and swiftly re-attach it to your phone the moment it is dry past pressing the sticky side firmly onto the dorsum of your phone.

   • Do non let your PopSocket dry for more than 15 minutes at most or information technology may lose its ability to stick.
   • If you accidentally leave it out, run information technology nether cold h2o for a few seconds so let it dry again, although be aware that it may non regain its stickiness.

   Advertisement

1. ane

   Remove any additional stickers you've added to the cease of the PopSocket. If you added stickers to the PopSocket's grip, you will need to remove them earlier you clean it. If the adhesive is still practiced on the sticker experience gratuitous to put it dorsum on after cleaning, otherwise you will take to simply throw it abroad and find a new i.

   • Popsockets usually come with some kind of pattern on the end of the grip, so fifty-fifty if you have to remove any boosted stickers you've added, information technology will still have an aesthetic design.^{[half dozen]}

2. two

   Remove the PopSocket and run the plastic grip under cold water. Use your fingernail to pry the PopSocket off of your phone, then hold the adhesive side of the PopSocket and plough your water faucet to a depression flow on cold. Run merely the plastic grip of the PopSocket under water — if y'all must, wrap the adhesive in a hand towel to prevent getting it wet and affecting its stickiness.

   • Yous can clean the adhesive separately, but if you get it wet earlier you're ready to clean it, you could cause the adhesive to lose some of its stickiness. Wrap it or accept care to not get it wet while cleaning the grip.

3. 3

   Scrub the plastic grip with the corner of a soapy rag, avoiding the adhesive. Hold the PopSocket by the viscous side again and scrub the plastic grip with the corner of a soapy rag PopSocket. Take care to avoid getting soap on the adhesive, and only scrub the plastic parts of the PopSocket.

   • Scrub inside the grooves of the PopSocket'south expandable center department with a cotton swab soaked in soapy h2o.
   • Apply 70 per centum rubbing booze to peculiarly stubborn stains or grime with a cotton swab, and then rinse it under h2o again. Rubbing alcohol is nifty for removing stains every bit it evaporates chop-chop and leaves no damage.

4. four

   Rinse the grip one time once again, then dry it with a paper towel or rag. Run the grip under water to get rid of soapy rest and rubbing alcohol, once again taking care to avoid getting the adhesive wet. Then, have a dry rag or a paper towel and dab the PopSocket dry until it is completely free of water.^[vii] Press it firmly onto the dorsum of your phone with the pasty-side down.

   • Yous can also air dry the plastic grip. Expand the PopSocket so residual information technology on its side on a paper towel. This prevents the adhesive from sticking to the towel and will even so allow the grip to air dry and drip dry.

   Advertisement

Inquire a Question

200 characters left

Include your email address to get a message when this question is answered.

Submit

Advertisement

• After re-attaching the PopSocket to your phone, wait at least 1 hr before y'all extend the grip and use it. This allows plenty fourth dimension for the adhesive to fully stick to your telephone, reducing the take chances of it detaching suddenly.^[8]

Thank you for submitting a tip for review!

Advertising

• Avoid using rubbing alcohol in a closed room, and take the PopSocket to a well-ventilated area to prevent inhaling rubbing alcohol fumes.

• Never let the sticky side of the PopSocket exist exposed to air for more than than xv minutes, even when cleaning the plastic grip, every bit this destroys the adhesive.

Advertisement

About This Article

Thanks to all authors for creating a folio that has been read 28,909 times.

Is this article upward to appointment?

turcottepaturs.blogspot.com

Source: https://www.wikihow.com/Clean-a-PopSocket